To estimate how much electricity does a sauna use, start with a simple formula: heater kW × hours at full power × your electricity rate. A 6 kW heater running at full power for one hour uses 6 kWh. Multiply that by the rate on your utility bill to estimate the electricity cost. Once the heater cycles on and off, that calculation gives you the most it could use during that time, not an exact reading.
You can get a useful estimate before you choose a sauna. You’ll need the heater rating, how long you’ll leave it on, and your utility rate. Count warm-up time separately from the time you spend inside.
How much electricity does a sauna use? Find the kW rating first
You’ll find the power rating on your heater’s nameplate, in its manual, or on its product page. If it’s listed in watts, divide by 1,000 to get kilowatts. For example, 1,750 W equals 1.75 kW. Voltage alone won’t tell you how much electricity a sauna uses.
When you compare sauna heaters, match the specific model to your room before you calculate electricity use. Don’t assume the model name gives you the exact kW rating. The HUUM DROP 4, for instance, is rated at 4.5 kW.
The HUUM DROP manual lists these ratings and room-volume ranges for its 240V heaters:
| Heater | Power | Room volume |
|---|---|---|
| DROP 4 | 4.5 kW | 106–248 cubic feet |
| DROP 6 | 6 kW | 177–318 cubic feet |
| DROP 7 | 7.5 kW | 248–389 cubic feet |
| DROP 9 | 9 kW | 283–460 cubic feet |
Use those ranges to compare HUUM sauna heaters, then follow the manual’s sizing adjustments for your room materials. Measuring the room gives you a starting point, but its materials also matter when you choose a heater.
Separate warm-up from holding temperature
Warm-up is the main stretch you’ll count at full power. HUUM says a properly insulated room with the right heater takes around one hour to reach temperature. Use that as a reference for your estimate. Your outdoor sauna won’t necessarily take that long every time.
The Harvia Spirit manual also describes about an hour for a properly insulated sauna to reach bathing temperature. Spirit heaters come in 6 kW and 8 kW versions at 240V, and Harvia suggests 149–176°F. Use the specific model’s rating when you compare Harvia sauna heaters.
Once the room reaches its set temperature, the heater cycles on and off. So an hour with the controls on doesn’t always mean an hour at full power. The clock alone can’t tell you exactly how much electricity the heater uses while holding temperature.
For a conservative estimate, count all powered-on time as full-power time. To get closer to actual use, you’ll need to know how long the heater draws full power. Don’t plug in a cycling percentage without knowing how your heater runs.
Calculate your sauna kWh and electricity cost
This table shows the most each heater could use in one hour at full power, based on its listed rating. These are calculation examples. They aren’t measured session totals, and they don’t tell you how long warm-up will take.
| Heater | kW | Max kWh for 1 hour at full power |
|---|---|---|
| HUUM DROP 4 | 4.5 | 4.5 kWh |
| HUUM DROP 6 | 6 | 6 kWh |
| HUUM DROP 7 | 7.5 | 7.5 kWh |
| HUUM DROP 9 | 9 | 9 kWh |
| Finnmark FD-2 | 1.75 | 1.75 kWh |
| Finnmark FD-3 | 3.15 | 3.15 kWh |
Say your 6 kW heater stays on for one hour of warm-up plus 30 minutes afterward. The full-power ceiling is 6 × 1.5 = 9 kWh. If the heater cycles off during that period, its actual electricity use will fall below that ceiling.
To estimate sauna electricity cost, call your utility rate R. The electricity charge for that full-power example is 9 × R. Take the rate per kWh from your bill and keep the units consistent throughout your calculation.
Rates vary by state and utility plan. The EIA’s average residential electricity prices by state give you a reference, but your own bill has the rate you need for your estimate. If your plan charges different rates at different times, use the rate for when you’ll run the sauna.
What changes your electricity estimate?
Room size, insulation and glass
Match your room volume to the heater’s sizing instructions. HUUM adds 3.3 cubic feet to the sizing calculation for each square foot of uninsulated brick, tile or glass wall. That’s why two rooms with the same dimensions may need different heater sizes.
The manufacturers’ roughly one-hour warm-up references assume proper insulation. When you compare outdoor saunas, look at how the room is built along with the heater rating. Outdoor temperature matters, too. Record your actual warm-up times through different seasons so you aren’t assuming every start takes an hour.
Door seals, vents and stones
According to LeisureCraft’s outdoor sauna maintenance guide, a good door seal keeps heat in. If your room won’t heat, look for a leaking door seal, blocked vents or tightly packed stones. Rule out those problems before you accept a long warm-up as normal.
Keep vents clear and follow your heater’s operating instructions. Harvia specifically says keeping the higher vent closed while heating helps the room heat faster. Follow the guidance for your own heater and setup. Our article on sauna ventilation explains more about how to review your setup.
How long and how often you use it
Count the entire time the heater is on, including warm-up. For a monthly ceiling, multiply your full-power session estimate by the number of sessions you expect to take. If your sessions run different lengths, calculate them separately and add the results. Mark that total as an estimate so you don’t confuse it with measured use.
Wood-burning and infrared options
Wood-burning heaters use no electricity. That tells you what the heater draws, but it doesn’t tell you the total cost of running a wood-burning sauna.
For infrared saunas, start with the listed wattage and how long you’ll run the sauna. Among our Finnmark saunas, the FD-2 is rated at 1,750 W on 120V, while the FD-3 is rated at 3,150 W on 240V. You’ll need both watts and hours to compare running costs.
Frequently asked questions
Does a sauna use a lot of electricity?
The answer depends on heater power and runtime. To answer how much electricity does a sauna use, calculate kWh first, then multiply by your utility rate. Count warm-up time, too. When the heater cycles on and off, the full-power calculation gives you a ceiling for electricity use.
Is an infrared sauna cheaper to run?
It depends on wattage and time. Multiply each model’s kW rating by the hours you expect to leave it on, then apply your utility rate. You can’t tell which sauna costs less to run from heater type alone.
Do I need a special circuit?
Have a licensed electrician review the circuit requirements for your exact model and home. Give them the manufacturer’s manual and read our guide to outdoor sauna electrical requirements. Your local building department can answer questions about applicable permits. Backyard America doesn’t install saunas, but we can help you find an installer and give you expert support by phone. Call us at 888-596-4403.